Pillar design

From QueensMineDesignWiki
Revision as of 15:31, 4 February 2015 by LKenny (talk | contribs) (2.3.2 Foundation Failure)

Jump to: navigation, search

1.0 Classification of Pillars

1.1 Support Pillars

Support pillars are load carrying. Examples of support pillars include:

Type of Pillar Description
Sill Pillar Horizontal pillars that separate levels or stopes, often used when multiple levels are mined concurrently.
Room and Pillars Pillars are left in place in a predetermined and calculated pattern as rooms are mined out.
Yield Pillars Pillars are designed to fail by going past peak load carrying capacity. Roof-strata is maintained by relieving pressure in working areas and controlling transference of load to abutments that are clear of working areas and road ways.Yielded pillars still carry load.
Post Pillars Room and pillar variation where ore is mined out in a series of horizontal slices.
Barrier Pillars Solid blocks left between two mines or sections of a mine. Provides regional support in large mines to prevent accidents due to inrushes of water, gas, or explosions or a mine fire.
Bracket Pillars Slip on discontinuities may cause rockburst within stopes, which can cause equipment damageand injury or loss of life. Ore immediately adjacent to these geological structures is left unmined to protect the structure from mining induced stresses.

1.2 Protection pillars

Protection pillars provide shelter in a mine. Examples of protection pillars include:

Type of Pillar Description
Shaft Pillars A large area that is left unworked around the shaft bottom to protect the shaft and the surface building from damage due to subsidence . Protects the shaft itself.
Crown Pillars A rock mass of variable geometry, mineralized or not, situated above an uppermost stope of the mine, which serves to permanently or temporarily ensure the stability of surface elements. Surface elements include bodies of water, soil and precipitation . Separate underground from surface mining.
Boundary Pillars Pillars left in mines between adjoining properties . Usually formed between mines.
Barrier Pillars Large pillar left unworked between two mines for security against accidents arising from an influx of water .
Bracket Pillars Slip on discontinuities may cause rockbursts within stopes, which can cause equipment damage and injury or loss of life. The most practical measure to counteract these effects involve leaving left over strips of unmined ground adjacent to the features to reduce potential for them to slip .

2.0 General Aspects of Pillars

2.1 Pillar design considerations

Pillar design considerations that need to be taken into account include :

  • Pillar load
  • Strength of pillars (failure criteria)
  • Orebody geometry
  • Geological characteristics of a mine
  • Load-deformation characteristics of the pillar and stiffness of the loading system

2.2 Pillar design basics

Pillar design basics are mainly concerned with:

  • Peak-pillar strength (load-bearing capacity)
  • Post-peak or load-deformation characteristics of a pillar

Pillar load and load distribution need to be established and potential failure models must be always kept in mind.

2.3 Potential Pillar Failure Modes

The strength of pillars are highly dependent on the geological conditions of the mine and there is no universal pillar design method. The following pictures show the potential failure modes that need to be considered for pillar design which are spalling (hourglassing), shear fracturing (geology and stress), bulking/bulging (geology) and foundation failure:


2.3.1 Hourglass Failure

The most common mode of failure is hourglassing. Hourglassing occurs when the sides of the pillar start to spall off due to high stresses, which are always highest on the boundary of the pillar. Due to this, bolting of the sidewalls of pillars is sometimes necessary. By keeping broken rock in place, it provides a form of confinement to the core and can prevent progressive failure and eventual collapse of the pillar. In the situation that there is a fault or large joint cutting the pillar, displacement on it will usually be the mode of failure .

2.3.2 Foundation Failure

The foundation of the pillar is a part of the load-carrying system and must be considered for the overall design. If the foundation rock is of low strength, it could fail prior to failure of the pillar itself. Pillar foundation is not always in the floor. For example, it can be in the hanging wall or footwall of sill pillars in steeply dipping deposits. This can be examined using numerical analysis to determine potential for foundation failure. Formulas are available for rib and rectangular pillars which relate foundation strength to the cohesion and friction angle of the foundation rock. If the foundation geology cannot be represented by a homogeneous isotropic elastic material, an analytical solution should not be used. The following picture shows the different forces associated with foundation failure and the yield zones : Please add a link to this page in the article that already exists on room and pillar mining.


The following chart is useful in estimating stress levels below a pillar with a circular footing which is found in many soil mechanics texts:


The contours on the chart show the fraction of the original surface load magnitude. The rule of thumb of stresses being concentrated in 45 degree zone beneath the foundation can be clearly seen in the chart, as this angle approximately defines the extent of the induced stress bulbs below the foundation .