Difference between revisions of "Vertical crater retreat"

From QueensMineDesignWiki
Jump to: navigation, search
Line 40: Line 40:
 
|
 
|
 
*The strength of the waste rock must be competent in order to blast against it without having excessively large amounts of dilution
 
*The strength of the waste rock must be competent in order to blast against it without having excessively large amounts of dilution
*The ore deposit is to be of medium to competent strength
+
*The ore deposit is to be of medium to competent strength <ref> Archibald, J. F. "Mining Systems and Methods." 2007. MINE 210. Department of Mining Engineering, Queen's University at Kingston. </ref>
   
 
|-
 
|-
Line 57: Line 57:
 
*Given the small, localized stope size in VCR&nbsp;mining, ore can be recovered very soon after blasting occurs.&nbsp; Therefore, oxidizing and self-cementing ores such as pyrrhotite can be mined using this method
 
*Given the small, localized stope size in VCR&nbsp;mining, ore can be recovered very soon after blasting occurs.&nbsp; Therefore, oxidizing and self-cementing ores such as pyrrhotite can be mined using this method
   
|}
+
|}
   
 
== Advantages ==
 
== Advantages ==

Revision as of 16:44, 9 February 2011

From Queen's University Mine Design Wiki


This article is about the orebody requirements and developmental steps involved in Vertical Crater Retreat planning and mining.


Vertical crater retreat (VCR), also known as Vertical retreat mining, is an open stoping, bottom-up mining method that involves drilling large-diameter holes into the orebody vertically from the top, and then blasting horizontal slices of thethe orebody into an undercut. 

Similar to Sublevel open stoping and Blasthole stoping methods, VCR mining is used for steeply-dipping (>45º), or both vertically and horizontally large orebodies with competent ore and waste rock strength.  It differs from other open stoping methods in that it is a bottom-up method, as opposed to a left-to-right method, and it does not require the excavation of sublevel drifts before blasting and mucking can take place.

Holes are typically 165mm in diameter, allowing for a blast pattern spacing of 4.0 by 4.0m, and the thickness of one slice of ore varies between 2 and 5m [1].

History

Orebody Characteristics

VCR is a suitable mining method for orebodies that exhibit the following characteristics:


Characteristic

Requirements

Orebody Dimensions                                           

  • Steeply-dipping orebodies (>45º), with widths of no less than 12-15m, or
  • Very large both vertically and horizontally
Ore and Rock Strength          
  • The strength of the waste rock must be competent in order to blast against it without having excessively large amounts of dilution
  • The ore deposit is to be of medium to competent strength [2]
Grade
  • VCR is not a selective mining method, therefore the ore grade should be low to medium, and it should be relatively uniform throughout the entire orebody
Depth
  • VCR mining can occur in mines at any depth.  Work is carried out in reinforced, small drifts; and given the nature of the mining method, no personnel has to work directly within the drift.  Therefore safe execution of VCR mining can be carried out in deep mines
Oxidizing Ores
  • Given the small, localized stope size in VCR mining, ore can be recovered very soon after blasting occurs.  Therefore, oxidizing and self-cementing ores such as pyrrhotite can be mined using this method

Advantages

Disadvantages

Mine Development

  1. "Vertical Crater Retreat -VCR." 2008. Atlas Copco. http://194.132.104.144/Websites%5CRDE%5Cwebsite.nsf/$All/2B0103C539FA78984125674D004AA392?OpenDocument
  2. Archibald, J. F. "Mining Systems and Methods." 2007. MINE 210. Department of Mining Engineering, Queen's University at Kingston.